canio – CAN bus access¶
The canio module contains low level classes to support the CAN bus
protocol.
CAN and Listener classes change hardware state and should be deinitialized when they
are no longer needed if the program continues after use. To do so, either
call deinit() or use a context manager. See
Lifetime and ContextManagers for more info.
For example:
import canio
from board import *
can = canio.CAN(board.CAN_RX, board.CAN_TX, baudrate=1000000)
message = canio.Message(id=0x0408, data=b"adafruit")
can.send(message)
can.deinit()
This example will write the data “adafruit” onto the CAN bus to any device listening for message id 0x0408.
A CAN bus involves a transceiver, which is often a separate chip with a « standby » pin. If your board has a CAN_STANDBY pin, ensure to set it to an output with the value False to enable the transceiver.
Other implementations of the CAN device may exist (for instance, attached via an SPI bus). If so their constructor arguments may differ, but otherwise we encourage implementors to follow the API that the core uses.
Available on these boards
- class canio.BusState¶
The state of the CAN bus
- ERROR_ACTIVE :object¶
The bus is in the normal (active) state
- ERROR_WARNING :object¶
The bus is in the normal (active) state, but a moderate number of errors have occurred recently.
Note
Not all implementations may use
ERROR_WARNING. Do not rely on seeingERROR_WARNINGbeforeERROR_PASSIVE.
- ERROR_PASSIVE :object¶
The bus is in the passive state due to the number of errors that have occurred recently.
This device will acknowledge packets it receives, but cannot transmit messages. If additional errors occur, this device may progress to BUS_OFF. If it successfully acknowledges other packets on the bus, it can return to ERROR_WARNING or ERROR_ACTIVE and transmit packets.
- BUS_OFF :object¶
The bus has turned off due to the number of errors that have occurred recently. It must be restarted before it will send or receive packets. This device will neither send or acknowledge packets on the bus.
- class canio.CAN(tx: microcontroller.Pin, rx: microcontroller.Pin, *, baudrate: int = 250000, loopback: bool = False, silent: bool = False, auto_restart: bool = False)¶
CAN bus protocol
A common shared-bus protocol. The rx and tx pins are generally connected to a transceiver which controls the H and L pins on a shared bus.
- Paramètres:
rx (Pin) – the pin to receive with
tx (Pin) – the pin to transmit with
baudrate (int) – The bit rate of the bus in Hz. All devices on the bus must agree on this value.
loopback (bool) – When True the
rxpin’s value is ignored, and the device receives the packets it sends.silent (bool) – When True the
txpin is always driven to the high logic level. This mode can be used to « sniff » a CAN bus without interfering.auto_restart (bool) – If True, will restart communications after entering bus-off state
- auto_restart :bool¶
If True, will restart communications after entering bus-off state
- baudrate :int¶
The baud rate (read-only)
- transmit_error_count :int¶
The number of transmit errors (read-only). Increased for a detected transmission error, decreased for successful transmission. Limited to the range from 0 to 255 inclusive. Also called TEC.
- receive_error_count :int¶
The number of receive errors (read-only). Increased for a detected reception error, decreased for successful reception. Limited to the range from 0 to 255 inclusive. Also called REC.
- state :BusState¶
The current state of the bus. (read-only)
- loopback :bool¶
True if the device was created in loopback mode, False otherwise (read-only)
- silent :bool¶
True if the device was created in silent mode, False otherwise (read-only)
- listen(matches: Sequence[Match] | None = None, *, timeout: float = 10) Listener¶
Start receiving messages that match any one of the filters.
Creating a listener is an expensive operation and can interfere with reception of messages by other listeners.
There is an implementation-defined maximum number of listeners and limit to the complexity of the filters.
If the hardware cannot support all the requested matches, a ValueError is raised. Note that generally there are some number of hardware filters shared among all fifos.
A message can be received by at most one Listener. If more than one listener matches a message, it is undefined which one actually receives it.
An empty filter list causes all messages to be accepted.
Timeout dictates how long receive() and next() will block.
Platform specific notes:
SAM E5x supports two Listeners. Filter blocks are shared between the two listeners. There are 4 standard filter blocks and 4 extended filter blocks. Each block can either match 2 single addresses or a mask of addresses. The number of filter blocks can be increased, up to a hardware maximum, by rebuilding CircuitPython, but this decreases the CircuitPython free memory even if canio is not used.
STM32F405 supports two Listeners. Filter blocks are shared between the two listeners. There are 14 filter blocks. Each block can match 2 standard addresses with mask or 1 extended address with mask.
ESP32S2 supports one Listener. There is a single filter block, which can either match a standard address with mask or an extended address with mask.
- send(message: RemoteTransmissionRequest | Message) None¶
Send a message on the bus with the given data and id. If the message could not be sent due to a full fifo or a bus error condition, RuntimeError is raised.
- __enter__() CAN¶
Returns self, to allow the object to be used in a
The with statementstatement for resource control
- __exit__(unused1: Type[BaseException] | None, unused2: BaseException | None, unused3: types.TracebackType | None) None¶
Calls deinit()
- class canio.Listener¶
Listens for CAN message
canio.Listeneris not constructed directly, but instead by callingcanio.CAN.listen.In addition to using the
receivemethod to retrieve a message or thein_waitingmethod to check for an available message, a listener can be used as an iterable, yielding messages until no message arrives withinself.timeoutseconds.- timeout :float¶
- receive() RemoteTransmissionRequest | Message | None¶
Reads a message, after waiting up to
self.timeoutsecondsIf no message is received in time,
Noneis returned. Otherwise, aMessageorRemoteTransmissionRequestis returned.
- __next__() RemoteTransmissionRequest | Message¶
Reads a message, after waiting up to self.timeout seconds
If no message is received in time, raises StopIteration. Otherwise, a Message or is returned.
This method enables the
Listenerto be used as an iterable, for instance in a for-loop.
- __enter__() CAN¶
Returns self, to allow the object to be used in a
The with statementstatement for resource control
- __exit__(unused1: Type[BaseException] | None, unused2: BaseException | None, unused3: types.TracebackType | None) None¶
Calls deinit()
- class canio.Match(id: int, *, mask: int | None = None, extended: bool = False)¶
Describe CAN bus messages to match
Construct a Match with the given properties.
If mask is not None, then the filter is for any id which matches all the nonzero bits in mask. Otherwise, it matches exactly the given id. If extended is true then only extended ids are matched, otherwise only standard ids are matched.
- id :int¶
The id to match
- mask :int¶
The optional mask of ids to match
- extended :bool¶
True to match extended ids, False to match standard ides
- class canio.Message(id: int, data: bytes, *, extended: bool = False)¶
Construct a Message to send on a CAN bus.
- Paramètres:
In CAN, messages can have a length from 0 to 8 bytes.
- id :int¶
The numeric ID of the message
- data :bytes¶
The content of the message
- extended :bool¶
True if the message’s id is an extended id
- class canio.RemoteTransmissionRequest(id: int, length: int, *, extended: bool = False)¶
Construct a RemoteTransmissionRequest to send on a CAN bus.
- Paramètres:
In CAN, messages can have a length from 0 to 8 bytes.
- id :int¶
The numeric ID of the message
- extended :bool¶
True if the message’s id is an extended id
- length :int¶
The length of the requested message.